Semitrone Conchem Private Limited
Semitrone Conchem Private Limited
Navrangpura, Ahmedabad, Gujarat
Send E-mail
Send SMS
Home  » Our Products  » 

CONSTRUCTION CHEMICAL


Leading Manufacturer of maxbond p. m. c., maxhard hd - m, maxhard nm, max repell, maxfiber and maxcrete gp / hs from Ahmedabad.

REQUEST CALLBACK
Ask for Price

Price on Request: Get Latest Price

Product Details:
Material Supply Service Provider End
FormLiquid
Packaging Size1 Ltr. + 4 Kg, 5 Ltr. + 20 Kg
Surface of ApplicationRoofs , Concrete
ColorWhite
Types Acrylic
MaterialAcrylic Polymer
Packaging TypeBAG
BrandSEMITRONE

Flexible, Acrylic Emulsion Mortar Modifier, Bonding Agent & Polymer Modified Cementitious Coating

MAXBOND P.M.C. is a two component, polymer modified, cementitious coating. Which is create non porous film on the substrate. MAXBOND P. M. C. consisting of cements, finely graded aggregates and a proprietary blend of additives which offer enhanced adhesion and flexibility.

primary applications

Concrete, Mortar or Masonry substrates

Terrace, Bathroom Sunk, Balcony, Basement Wall etc.

Interior or Exterior

Over Head Tank, Under Ground Tank, Canal, Dam etc.

Advantage

Provides a non porous substrate

Breathable & Low odor

Enhances abrasion resistance

Provides a protective waterproof coating

Resist water pressure up to seven meter head

Can be applied directly to concrete and masonry with minimum surface preparation

Provides high resistance to carbon dioxide and chloride ion diffusion

Can inject in cracks with micro cement slurry

Surface Preparation

Surfaces to receive MAXBOND PMC must be structurally sound, clean and free of dirt, oil and all other contaminants. Mechanically abrade the surface to remove laitance, coatings, deteriorated concrete, or other contaminants which might interfere with adhesion. Cracks, spalls and damaged concrete must be repaired and patched.

Mixing

Mix complete kit. Place approximately 1/2 of liquid Part B in a clean container. Use a 1/2" (13 mm) drill and a mixer at slow speed. While mixing, slowly add all Part A powder to produce a smooth paste with no lumps. Add remaining liquid of Part B and continue mixing until uniformly blended. Do not aerate the mix. After mixing, allow 05 to 07 minutes for the mix to thicken. Remix before application.

Application

For porous surfaces or when applying in direct sunlight, pre-dampen the surface, but ensure that it is free of any standing water prior to application. MAXBOND PMC can be applied by spraying, rolling or brushing. If brush applied use a high quality brush. Load the bristles with MAXBOND PMC and apply the coating using long, smooth strokes. Final strokes should be in one direction to produce a uniform appearance. A Hopper type spray gun may be used to spray the coating. Two coats, each at 10 to 16 mils, are recommended for optimum performance. Allow the first coat to cure for at least 8 hrs, but less than 24 hrs, before application of the second coat.


Yes! I am Interested


REQUEST CALLBACK
Ask for Price

Price on Request: Get Latest Price

Product Details:
Packaging TypeBAG
ColorFRENCH GRAY
MaterialHeavy Duty Metallic Floor Hardener
ApplicationFloor Hardener
BrandSEMITRONE

Description

MAXHARD HD - M is a dry shake, metallic floor hardener with graded iron aggregate in a high strength cementitious binder. Designed to be incorporated into fresh concrete slabs, It provides a dense, tough surface capable of with standing the abrasion and impact loading seen by floor slabs of numerous industrial and manufacturing facilities. MAXHARD HD - M has been specially formulated with a non-rusting aggregate for increased abrasion resistance in areas subject to frequent moisture or water exposure.

Features/Benefits

- Provides a high strength wearing surface in areas subject to constant or

frequently wet conditions without oxidizing.

- Gives up to 6 times the abrasion resistance of plain, cured concrete.

- Iron aggregate is free of rust, oil, or other contaminants.

- Dense surface resists penetration of oil, grease, and many other liquids.

- Virtually non-dusting in service.

- Easy to clean and maintain

- Economical to own over the life of the floor.

- Can be applied at coverage rates up to 5 to 12 kg/m

- Available in 5 standard colours.

Primary Applications

- Industrial floors

- Loading docks

- Warehouses

- Main, high traffic aisleways

- Processing plants

- Passenger and freight terminals

- Distribution centers

Standard Colours

French Gray, Black, Brick Red, Tera Cotta, Green. The final finish can be any texture normally achievable with concrete and should be specified by the owner.

Application Tips

Colored (pigmented) dry shakesrequire special attention for a uniform colour. Care should be taken with regard to the following; delay application of the shake as long as possible to get the maximum colour saturation at the surface of the slab, apply the shake as evenly as possible and in two applications for maximum uniformity, do not burnish trowel the floor. Best appearance is achieved by hand trowelling the final finish.

Curing and Sealing

Curing and sealing MAXHARD HD-M may be done with either a MAXROTH CHEMICALS water based or solvent based MAXCURE, or cure and seal. Each has its own advantages and unique properties. Consult the individual technical data sheet for each curing and sealing product or contact your Maxroth Chemical Company representative for a recommendation regarding your specific project.

Technical Details

Colur French Gray, Black, Brick Red, Tera Cotta, Green

Hard Aggregate (Aluminium Oxide) 50 %

Iron Particles As per IS standard

Compressive Strength as per IS 516 - 1959

# 60 N/mm to 70 N/mm


Yes! I am Interested


REQUEST CALLBACK
Ask for Price

Price on Request: Get Latest Price

Product Details:
Quantity Per Pack20KG BAG
ColorGRAY
BrandSEMITRONE
MaterialNon-Metallic Floor Hardener
ApplicationFloor Hardener

MAXHARD NM

Non-Metallic Floor Hardener

Description

MAXHARD NMis a quartz-silica mixture of finely graded non-metallic aggregates, plasticizer and cement binder. It is non rusting floor hardening compound having high wear resistance, high impact resistance concrete floor hardener recommended for both interior and exterior use. It is particularly valuable because of its non-rusting characteristics when floors will be frequently wet. MAXHARD NM is available in non-fading colours in addition to the standard natural cement colour.

Features/Benefits

- Hardens concrete in one economical operation.

- Use of hard and properly graded aggregates increases the wear resistance over plain

concrete floors.

- Increases impact and abrasion resistance up to twice that of plain concrete.

- Ready-to-use factory blend eliminates messy and expensive job mixing and minimizes

Errors.

- Non-rusting materials make it possible to use MAXHARD NM outdoors as well as

Indoors.

Primary Applications

- Commercial and industrial facilities

- Lobbies and waiting rooms of commercial and public buildings

- Corridors and washrooms in institutional and public buildings

- Auto showrooms and service centers

- Factory and warehouse floors

- Restaurants and dairies

Standard Colours

French Gray, Black, Brick Red, Tera Cotta, Green. The final finish can be any texture normally achievable with concrete and should be specified by the owner.

Application Tips

Colored (pigmented) dry shakesrequire special attention for a uniform colour. Care should be taken with regard to the following; delay application of the shake as long as possible to get the maximum colour saturation at the surface of the slab, apply the shake as evenly as possible and in two applications for maximum uniformity, do not burnish trowel the floor. Best appearance is achieved by hand trowelling the final finish.

Curing and Sealing

Curing and sealing MAXHARD NM may be done with either a MAXROTH CHEMICAL water based or solvent based MAXCURE, or cure and seal. Each has its own advantages and unique properties. Consult the individual technical data sheet for each curing and sealing product or contact your MAXROTH CHEMICAL Company representative for a recommendation regarding your specific project.

Coverage

MAXHARD NM may be applied at rates from 2.4 to 9.8 kg/m. Higher application rates yield better total abrasion resistance. Greater application rates may be used with special considerations. Contact your Maxroth Chemicals Company representative for recommended procedures.

Packaging & Shelf Life

MAXHARD NMpackaged in 25 kg bags with polyethylene liners for moisture protection. 2 year in original, unopened package.


Yes! I am Interested


REQUEST CALLBACK

Price on Request: Get Latest Price

Product Details:
FormLiquid
TypeConstruction Adhesives & Sealants
CategoryWaterproofing Coating, Cementitious Waterproofing
ApplicationWalls
Packaging Size10kg, 20kg
BrandSEMITRONE
FlammableYes
Packaging TypeBucket
Form of ChemicalsLiquid
ColorWhite Crystal
UsageCONSTRUCTION CHEMICAL
Form of ChemicalLiquid

MAX REPELL clear silicon water repellent is a double strength, solvent based water repellent designed for use in the most exposed areas. It is based on poly ox aluminium stearate in a solvent solution and is used for protecting brick, stone, concrete and other masonry against penetration of rainwater and lateral dampness. It comes in liquid form and can be applied by brush or low - pressure spray.

Benefits

·          Increases substrate weather ability, provides moisture protection, and resists staining

·         Protects substrate against freeze thaw cycles; allows for easy maintenance

·         Long-term performance

·         Applied using a brush, roller, or sprayer and cleans up with water

·         Clear with a non-sheen finish to preserve the natural look

·         Allows wall to naturally breath

·         Low odor and toxicity

Features

·          Repellent

·          Chemical and UV Resistant

·          Easy to Use

·          Natural Finish

·         Highly Vapor permeable

Primary Applications

·         Stucco

·         Masonry

·         Poured-in-place and/or Tilt-up concrete

·         Cementitious surfaces

·         Approved interior products

  • Porous tile, brick, stone, and slate

Surface Preparation 

All surfaces to receive application must be fully clean and free of debris, dirt, dust, efflorescence, grease, oils, curing agents, paint and cleaning solutions. Protect adjacent surfaces from unintentional application of Water Repellent.

 

Application Tips

MAXREPELL can be applied by brush, roller or spray. Do not thin or dilute. Consult guidelines for specific type of application or substrate to be coated for detailed preparation, application and coverage information.

 

     

    Packaging :        Available in 5 Ltr., 20 Ltr. & 50 Ltr., container


    Yes! I am Interested


    REQUEST CALLBACK

    Price on Request: Get Latest Price

    Product Details:
    TypesCeramic
    Grade StandardIndustrial Grade, Chemical Grade
    Surface of ApplicationCeramic
    BrandSEMITRONE
    FormPowder
    FeaturesWater Resistant, Moisture Resistant, Impact Resistant
    Application Tile On Tile, Tile Fixing

    MAXFIBER ispolymerized propylene; a very light, Highly resistant, Emerging as true crack-control reinforcement, "structural" fibers have gained a stronger foothold in concrete. It is the most common material for making microfibers because of its alkali resistance.

    • Reduced Bleeding
    • Flexural Toughness
    • Enhanced Impact Resistance
    • Fire Resistance

    Note Fibers has various advantages over other fibers available in Indian market. These fibers have been developed after various research and field trials. The fibers have been designed specifically to give better results when used in concrete.


    Yes! I am Interested


    REQUEST CALLBACK

    Price on Request: Get Latest Price

    Product Details:
    TypesCeramic
    FormPowder
    TypeWater Proofing Compounds
    Surface of Application Glass, Ceramic
    ApplicationRoofs, Terrace
    Packaging Size10KG 20KG
    BrandSEMITRONE
    Features Moisture Resistant
    FlammableYes
    Packaging TypePacket
    Categories Cementitious, Epoxy

    GP - General Purpose, HS - High Strength Non - Shrink Free Flow Cementitious Grout

    DESCRIPTION

    MAXCRETE GP / HS are specially formulated Non- shrink, Chloride free & free & free flow grout. It is used as a non- shrinking, volume constant pouring compound in civil engineering construction for casting between foundation & machinery, turbines etc. it gives high early strength, strength, excellent workability and available in two different grades.

    FEATURES/BENEFITS

    • Trouble free performance
    • Gaseous expansion system compensates for shrinkage problems its original volume during curing.
    • Control expansion ensures surface contact after setting.
    • High ultimate strength combined with dense impermeable structure.
    • No metallic particle so none rusting, No metallic iron content to corrode, and cause staining or deterioration due to rust expansion.
    • Imparts high frost, fire and oil resistance.

    PRIMARY APPLICATION

    • Pumps & Fans
    • Generators
    • Anchor Bolts
    • Compressor & Motors
    • All types of Machine bases
    • Column Base plates
    • Heavy Duty Grouting of Machinery & Equipments

    APPLICATION TIPS

    General Information While MAXCRETE GP / HS is designed to be fluid poured at temperatures ranges from 5 to 38 C) the product is most easily poured at temperatures of 16 C to 21 C.

    Mixing Where MAXCRETE GP / HS will be placed at a thickness over 2" (50 mm), up to 9.1 kg of fine aggregate must be added to each bag of grout. Note that the water demand to achieve a certain flow level of the grout will change.

    Placing MAXCRETE GP / HS should be placed continuously.

    CURING & SEALING

    Proper curing procedures are important to ensure the durability and quality of the grout. Wet cure the grout until the forms is stripped. Then, cure the grout with a high solids curing compound, such as MAXROTH CHEMICALS water based or solvent based MAXCURE, or cure and seal. Each has its own advantages and unique properties. Consult the individual technical data sheet for each curing and sealing product or contact your Maxroth Chemical Company representative for a recommendation regarding your specific project.


    Yes! I am Interested


     

    Explore More Products
     

     

    Send SMS
    Semitrone Conchem Private Limited
    Mukesh Shah
    2nd Floor, Neelmani Chambers
    Navrangpura, Ahmedabad - 380009 , Gujarat , India
    Send E-mail
    Share Us:
    X